绝缘固体的耐介电强度测试设备/耐压设备/耐电压仪器
一、应用范围：
First, the scope of application:
ZJC-150KV主要适用于固体绝缘材料如电线套管、树脂和胶、浸渍纤维制品、云母及其制品、塑料、薄膜复合制品、陶瓷和玻璃等介质在工频电压或直流电压下击穿强度和耐电压时间的测试；采用计算机控制，可对试验过程中的各种数据进行快速、准确的采集、处理，并可存取、显示、打印。
ZJC-150KV is mainly applicable to solid insulating materials such as wire tube, resin and rubber, impregnated fiber products, mica products, plastic film, and composite products, ceramic and glass medium in the frequency of the voltage or DC voltage breakdown strength and voltage withstand test time; using computer control, the various test data process the fast and accurate data acquisition, processing, and storage, display and print.
二、满足标准：
Two, meet the standard:
1、GB1408.1-2006《绝缘材料电气强度试验方法》
1, GB1408.1-2006 "electrical strength of insulating materials test method"
2、GB1408.2-2006《绝缘材料电气强度试验方法
2, "GB1408.2-2006 electrical strength of insulating materials test methods
第2部分：对应用直流电压试验的附加要求》
Part second: Additional requirements for tests using direct voltage "
3、GB/T1695-2005《硫化橡胶工频击穿电压强度和耐电压的测定方法》
3, GB/T1695-2005 "vulcanized rubber power frequency breakdown voltage strength and resistance to voltage measurement method"
4、GB/T3333 电缆纸工频电压击穿试验方法
4, GB/T3333 cable paper power frequency voltage breakdown test method
5、HG/T 3330绝缘漆漆膜击穿强度测定法
5, HG/T 3330 insulation paint film breakdown strength test method
6、GB12656 电容器纸工频电压击穿试验方法
6, GB12656 capacitor paper power frequency voltage breakdown test method
7、ASTM D149《固体电绝缘材料工业电源频率下的介电击穿电压和介电强度的试验方法》
7. D149 ASTM test method for dielectric breakdown voltage and dielectric strength of solid electrical insulating material industrial power frequency
三、主要技术指标：
Three, the main technical indicators:
1、输入电压 AC220V 50Hz
1, the input voltage AC220V 50Hz
2、输出电压： AC：0～150kV； DC：0～150kV
2, output voltage: AC:0 DC:0 ~ 150kV ~ 150kV;
3、输出功率： 15kVA
3, output power: 15kVA
4、测量范围： AC15～150kV； DC15～150kV
4, measuring range: AC15 DC15 ~ 150kV ~ 150kV;
5、测量误差： ≤ 2％
5, measurement error: = 2%
6、升压速率： 1kV/s～5kV/s
6, pressure rate: 1kV/s ~ 5kV/s
7、耐压时间： 0～4H
7, pressure time: 0 ~ 4H
8、漏电流 1～30 mA可由计算机软件自由进行设定
8, the leakage current 1 ~ 30 mA can be set free by computer software
9、电源 交流220V±10%的单相交流电压和50Hz±1%的频率
9, the power AC 220V + 10% single-phase AC voltage and frequency of 50Hz + 1%
10、试验环境温度： 15 ～ 30℃，相对湿度：0～85%能够稳定运行。
10, the test environment temperature: 15 ~ 30 degrees, relative humidity: 0 ~ 85% can be stable operation.
11、外形尺寸长×宽×高：1980mm×1220 mm×1750mm（参考）
11, appearance size length * width * height: 1980mm * 1220 mm * 1750mm (Reference)
12、设备自重： 350Kg（参考）
12, equipment weight: 350Kg (Reference)
13、接地要求仪器需要单独接地，接地附合国家标准要求，金属棒深埋地下至少要1.5米以下
13, grounding requirements instruments need to be grounded alone, grounding with the national standard requirements, the metal rod buried at least 1.5 meters below the depth
四、结构原理及性能特点：
Four, structural principle and performance characteristics:
1、主要由：升压系统(高压变压器)、测量系统、A/D转换器、放电系统、电极、油箱、电极定位架、计算机数据处理系统、软件等组成；
1, mainly by: boost system (high voltage transformer), measurement system, A/D converter, discharge system, electrode, fuel tank, electrode positioning frame, computer data processing system, software and so on;
2、计算机---A/D转换器---测量控制系统---调压装置----升压变压器-----试样；
2, the computer ---A/D converter --- measuring control system --- voltage regulator -- the test sample;
3、高压变压器主要产生试样所需的直流电压；
3, high voltage transformers are mainly generated by the DC voltage of the sample;
4、调压器用于调节升压变压器输入端电压以产生高压所需的输入电压；
4, the regulator is used to adjust the input voltage of the boost transformer to generate the required input voltage;
5、电压测量主要是从高压变压器测量端测量，高压变压器测量端和高压端是线性的；
5, voltage measurement is mainly from the measurement of high voltage transformer measurement, high voltage transformer measurement and high pressure side is linear;
6、放电系统在试验做完以后放电，以免产生放电对人身的危害；
6, discharge system in the experiment after the discharge, so as to avoid discharge on the human body harm;
