圆高塑料 PA6 B40 德国巴斯夫 上海出

Ultramid PA6: B4001, performance characteristics: oil resistance, high viscosity. Application: film, multilayer film, monofilament, casting film.

Ultramid (Germany) PA6: B40L01, additive: lubricant. Properties: lubrication, high viscosity. Application: film, monofilament, casting film.

Ultramid (Germany) PA6: B40L, additive: lubricant. Properties: lubrication, oil resistance, high viscosity. Application: film, monofilament, casting film.

Ultramid (Germany) PA6: B40LN, additive: nucleating agent, slippage agent. Properties: smooth, nucleated, oil resistant, high viscosity. Application: film, casting film.

Ultramid PA6: B40, performance characteristics: oil resistance, high viscosity. Way: film, monofilament, casting film

（3）尼龙66    PA66

A3HG5：特殊级，适合25%玻纤增强得制品

A3KG24：低粘度，适合一般通用的制品

A3KN：低粘度，适合成型周期快，产量高，一般通用的制品

A3R：特殊级，适合耐摩擦、耐磨耗性得制品

A3W：特殊级，低粘度，适合一般通用制品和耐热性好的制品

A3WG6：特殊级，适合30%玻纤增强的制品

A3WG7：特殊级，适合35%玻纤增强得制品

A3WG10：特殊级，适合50%玻纤增强得制品

A4：适合其他用途得制品

A4H：中粘度，适合一般通用得制品

A5W：高粘度，适合一般通用的制品和其他得工程制品

A3：低粘度，一般用的制品

A3EG3：注塑增强级，含15%玻纤增强

A3EG5：注塑增强级，含25%玻纤增强

A3EG6：注塑增强级，含30%玻纤增强

A3EG7：注塑增强级，含35%玻纤增强

A3EG10：注塑增强级，含50%玻纤增强

A3HG7：注塑增强级，含玻纤增强制品

A3K：低粘度，一般用得制品

A3WG5：注塑增强级，含25%玻纤增强

A3WG5MI：注塑级，加二硫化钼，适合耐摩擦磨耗性得制品

A3WC4：改进增强级，含20%碳纤维制品

A3XG5：阻燃增强级，含25%玻纤增强得UL94V-0

A3XG7：阻燃增强级，含35%玻纤增强得UL94V-0

A3Z：注塑级，耐冲击得制品

A3ZG6：耐冲击增强级，含30%玻纤增强

A3ZM4：耐冲击级，含20%矿物质增强改性得制品

A5：高粘度，一般用得制品

A38K：注塑级，成型周期快，产量高，质优

A3M6：共聚物，含30%矿物质增强得制品

C3M8：共聚物，含40%矿物质增强得制品

KR4205：阻燃级，非增强型，UL94V-0

KR4281：注塑改性级，含40%矿物质增强改性制品

KR4650：特殊级，适合矿物质增强改性工程制品

 

Mold temperature:

At 80-90℃, mold temperature significantly affects crystallinity, which in turn affects the mechanical properties of plastic parts. Crystallization for structural parts

Degrees are very important, so it is recommended that the mold temperature be 80-90℃. Higher mold temperatures are also recommended for thin - walled, longer - flow plastics. increase

Large die temperature can increase the strength and stiffness of plastic parts, but reduce the toughness. If the wall thickness is greater than 3mm, a low temperature of 20-40℃ is recommended

The mold. For glass fiber reinforced material mold temperature should be greater than 80℃.