采用具有世界先进水平的压铸机生产的管式正极板使电池寿命大大延长。
The life of batteries is greatly prolonged by using tubular cathode plate produced by die casting machine with world advanced level.
·电池外壳强度高，不易破裂。
· The battery shell has high strength and is not easy to crack.
·独特的透气盖设计，可有效防止电池内电解液溅出。
· Unique design of air permeability cover can effectively prevent electrolyte from splashing out in batteries.
·防爆性在电池盖部分加装特殊的装置，消氢排气栓，确保使用过程中氢气析出量达到安全标准，不会产生火花，避免引发爆炸。
· The explosion-proof part of the battery cover is equipped with a special device to eliminate hydrogen exhaust plug, so as to ensure that the amount of hydrogen released in the process of use meets the safety standards, does not generate sparks, and avoids the initiation of explosion.
·不漏液 采用热封技术和独特的透气盖设计，可有效防止电池内电解液漏出。
· The leak-free electrolyte can be effectively prevented by using heat sealing technology and unique air permeability cover design.
·无污染 使用过程中无废气排放，保证工作环境清洁
· No exhaust gas emission during non-polluting use to ensure clean working environment
电池不宜放电至低于预定的终止电压，否则将导致过放电，而反复的过放电则会导致容量难以恢复，为达到的工作效率，放电应0.05-2C 之间，放电终止电压如上表1所示。
Batteries should not discharge below the predetermined termination voltage, otherwise it will lead to overdischarge, and repeated overdischarge will lead to capacity recovery. In order to achieve the best efficiency, discharge should be between 0.05-2C, discharge termination voltage as shown in Table 1 above.
放电后请迅速充电，特别是在深放电后更应立即充电，否则将可能导致电池容量无法恢复。
Please charge quickly after discharging, especially after deep discharging. Otherwise, the battery capacity may not be recovered.
放电时请将电池温度控制在-15～50℃。
When discharging, please control the temperature of the battery to - 15 - 50 C.
有人说，“活性物质脱落使电池失去了容量”。如果脱落是唯一的原因，那么只有用机械办法包裹正极板，使活性物质不能脱落，汤浅蓄电池不就能无限期的使用吗？实际并不是这样，活性物质微观结构的变异也是丧失活性的重要原因，这里不再详述。
Some people say that "the removal of active substances makes the battery lose capacity". If falling off is the only reason, then only by wrapping the positive plate mechanically, so that the active material can not fall off, Tangshao battery can not be used indefinitely? In fact, this is not the case. The variation of the microstructures of active substances is also an important reason for the loss of activity. This is not detailed here.
使用中的耐普蓄电池，其正极板上Pb02与PBS04共存，负极上Pb与PBS04共存。在图1-2和充放电反应方程式中，充电后正极上都是Pbo2，负极上都是Pb。实际使用中的汤浅蓄电池的反极充电时不可能将其极板上的PBSO4完全转化成Pbo2或Pb。如果每次充放电循环都百分之百转化完，势必大大延长充放电时间。由于充电后期充电效率很低，大部分电流消耗于水的分解上。正极上分解水时产生新生态的氧原子，在两个氧原子合并成一个极分子之前，其氧化腐蚀能力极强，这就加剧了正极板栅的腐蚀，而且纯一氧化铅的结合力很差，易造成大量脱粉。为了延长铅蓄电池的使用寿命，没有必要为恢复少量的容量而付出板栅被腐蚀的沉重代价。同时在很多情况下，工作条件不允许长时间地把充电机给少数电池使用。由于以上原因，每经过一个充放电循环，都会有一部分活性物质转化为PBSO4而失去活性。正是这种缓慢的蚕食，一点一点地使电池失去了原始的容量。
Lead 02 and PBS04 coexist on the positive plate and PBS04 on the negative plate of the used Nipple battery. In Fig. 1-2 and the charge-discharge reaction equation, both the positive and negative electrodes are Pbo2 after charging. It is impossible to completely convert PBSO4 on the plate of Tangshao battery into Pbo2 or Pb when it is charged by the reverse electrode. If every charge-discharge cycle is converted to , the charge-discharge time will be greatly prolonged. Because of the low charging efficiency in the later stage of charging, most of the current is consumed by the decomposition of water. When water is decomposed on the cathode, new ecological oxygen atoms are produced. Before the two oxygen atoms merge into one polar molecule, their oxidation corrosion ability is very strong, which aggravates the corrosion of the cathode grid. Moreover, the binding force of pure lead monoxide is very poor, and it is easy to cause a large number of dedusting. In order to prolong the service life of lead-acid batteries, it is unnecessary to pay a heavy price for the corrosion of grids to recover a small amount of capacity. At the same time, in many cases, working conditions do not allow long-term use of the charger to a few batteries. Because of the above reasons, some active substances will be converted into PBSO4 and lose their activity after each charge-discharge cycle. It is this slow encroachment that makes the battery lose its original capacity bit by bit.
因为科学技术的不断发展和进步,现在人们的日常生活已经是离不开蓄电池的使用,而它的其中一种类型就是阳光蓄电池,相信大家对此也不感到陌生,但是在它的安装方面却了解的很少,因此今天德国阳光蓄电池公司的人在这就为大家来介绍下具体的安装要点.首先是第一步,工作人员要将安装环境的温度和通风要求进行一个测量,因为如果工作环境不达标的话是很容易会影响到阳光蓄电池的使用性能和效果的.其次就是要注意的是,大家在安装该蓄电池的时候千万不要直接放置在阳光下面,只要适当的温度就可以了,不然是很容易会给蓄电池带来伤害的.另外升降晾衣架制造公司在这还要提醒大家,为了避免蓄电池不能正常使用,大家在安装的时候一定要安装说明书上的内容进行操作,这样一来蓄电池的安装工作才算顺利完成.
Because of the continuous development and progress of science and technology, people's daily life has been inseparable from the use of batteries, and one of its types is sunlight batteries, I believe you are not unfamiliar with this, but in its installation, but little is known, so today the German Sunshine Battery Company people in this big. The first step is to measure the temperature and ventilation requirements of the installation environment. If the working environment is not up to the standard, it will easily affect the performance and effect of the solar battery. The second step is to pay attention to the installation of the battery. Never put it directly under the sun, as long as the proper temperature is enough, otherwise it will easily cause damage to the battery. In addition, the clothes hanger manufacturing company also reminds you that in order to avoid the normal use of the battery, you must install the contents of the instructions to operate when installing it. In this way, the installation of batteries can be completed smoothly.
